ASTM F1504-21e1

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
´1
Designation:F1504 −21
Standard Specification for
Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer
1
and Conduit Rehabilitation
This standard is issued under the fixed designation F1504; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Table 3 was editorially corrected in August 2022.
1. Scope* mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This specification covers requirements and test methods
for materials, dimensions, workmanship, flattening resistance,
2. Referenced Documents
impact resistance, pipe stiffness, extrusion quality, and a form
2
2.1 ASTM Standards:
of marking for folded poly(vinyl chloride) (PVC) pipe for
D618 Practice for Conditioning Plastics for Testing
existing sewer and conduit rehabilitation.
D790 Test Methods for Flexural Properties of Unreinforced
1.2 Folded PVC pipe produced to this specification is for
and Reinforced Plastics and Electrical Insulating Materi-
use in non-pressure sewer and conduit rehabilitation where the
als
folded PVC pipe is inserted into and then expanded to conform
D1600 Terminology forAbbreviatedTerms Relating to Plas-
to the wall of the original conduit forming a new pipe-within-
tics
a-pipe.
D1784 Classification System and Basis for Specification for
NOTE 1—For installation procedures and engineering design consider-
Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlo-
ations refer to Practice F1947.
rinated Poly(Vinyl Chloride) (CPVC) Compounds
F1947 Practice for Installation of Folded Poly(Vinyl Chlo-
1.3 This specification includes folded PVC pipe made only
ride) (PVC) Pipe into Existing Sewers and Conduits
from materials specified in Section 6. This specification does
not include folded pipe manufactured from reprocessed, D2122 Test Method for Determining Dimensions of Ther-
moplastic Pipe and Fittings
recycled, or reclaimed PVC.
D2152 Test Method for Adequacy of Fusion of Extruded
1.4 The values stated in inch-pound units are to be regarded
Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by
as standard. The values given in parentheses are mathematical
Acetone Immersion
conversions to SI units that are provided for information only
D2412 Test Method for Determination of External Loading
and are not considered standard.
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.5 The following precautionary statement pertains to the
D2444 Practice for Determination of the Impact Resistance
test method portion only, Section 11, of this specification: This
of Thermoplastic Pipe and Fittings by Means of a Tup
standard does not purport to address all of the safety concerns,
(Falling Weight)
if any, associated with its use. It is the responsibility of the user
F412 Terminology Relating to Plastic Piping Systems
of this standard to establish appropriate safety, health, and
F1057 Practice for Estimating the Quality of Extruded Poly
environmental practices and determine the applicability of
(Vinyl Chloride) (PVC) Pipe by the Heat Reversion
regulatory limitations prior to use.
Technique
1.6 This international standard was developed in accor-
3
2.2 Federal Standard:
dance with internationally recognized principles on standard-
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
ization established in the Decision on Principles for the
3
2.3 Military Standard:
Development of International Standards, Guides and Recom-
MIL-STD-129 Marking for Shipment and Storage
1 2
This specification is under the jurisdiction ofASTM Committee F17 on Plastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Piping Systems and is the direct responsibility of Subcommittee F17.67 on contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Trenchless Plastic Pipeline Technology. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Aug. 1, 2021. Published August 2021. Originally the ASTM website.
ɛ1 3
approved in 1994. Last previous edition approved in 2021 as F1504 –14(2021) . Available from DLA Document Services Building 4/D 700 Robbins Avenue
DOI: 10.1520/F1504-21E01. Philadelphia, PA 19111-5094 http://quicksearch.dla.mil/
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
...