ASTM F2599-22
(Practice)Standard Practice for Sectional Repair of Damaged Pipe By Means of an Inverted Cured-In-Place Liner
Standard Practice for Sectional Repair of Damaged Pipe By Means of an Inverted Cured-In-Place Liner<rangeref></rangeref >
SIGNIFICANCE AND USE
4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of pipes through the use of a resin-impregnated tube installed within a damaged existing host pipe. As for any practice, modifications may be required for specific job conditions.
SCOPE
1.1 This practice covers requirements and test methods for the sectional cured-in-place lining (SCIPL) repair of a pipe line (4 in. through 60 in. (10.2 cm through 152 cm)) by the installation of a continuous resin-impregnated-textile tube into an existing host pipe by means of air or water inversion and inflation. The tube is pressed against the host pipe by air or water pressure and held in place until the thermoset resins have cured. When cured, the sectional liner shall extend over a predetermined length of the host pipe as a continuous, one piece, tight fitting, corrosion resistant, and verifiable non-leaking cured-in-place pipe.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 There is no similar or equivalent ISO Standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2599 − 22
Standard Practice for
Sectional Repair of Damaged Pipe By Means of an Inverted
1,2
Cured-In-Place Liner
This standard is issued under the fixed designation F2599; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This practice covers requirements and test methods for
thesectionalcured-in-placelining(SCIPL)repairofapipeline
2. Referenced Documents
(4 in. through 60 in. (10.2 cm through 152 cm)) by the
3
2.1 ASTM Standards:
installation of a continuous resin-impregnated-textile tube into
C1920 Practice for Cleaning of Vitrified Clay Sanitary
an existing host pipe by means of air or water inversion and
Sewer Pipelines
inflation. The tube is pressed against the host pipe by air or
D790 Test Methods for Flexural Properties of Unreinforced
waterpressureandheldinplaceuntilthethermosetresinshave
and Reinforced Plastics and Electrical Insulating Materi-
cured. When cured, the sectional liner shall extend over a
als
predetermined length of the host pipe as a continuous, one
D1149 Test Methods for Rubber Deterioration—Cracking in
piece, tight fitting, corrosion resistant, and verifiable non-
an Ozone Controlled Environment
leaking cured-in-place pipe.
D1600 TerminologyforAbbreviatedTermsRelatingtoPlas-
1.2 The values stated in inch-pound units are to be regarded
tics
as standard. The values given in parentheses are mathematical
D2990 Test Methods for Tensile, Compressive, and Flexural
conversions to SI units that are provided for information only
Creep and Creep-Rupture of Plastics
and are not considered standard.
D3681 TestMethodforChemicalResistanceof“Fiberglass”
1.3 There is no similar or equivalent ISO Standard. (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a
Deflected Condition
1.4 This standard does not purport to address all of the
D5813 Specification for Cured-In-Place Thermosetting
safety concerns, if any, associated with its use. It is the
Resin Sewer Piping Systems
responsibility of the user of this standard to establish appro-
F412 Terminology Relating to Plastic Piping Systems
priate safety, health, and environmental practices and deter-
F1216 Practice for Rehabilitation of Existing Pipelines and
mine the applicability of regulatory limitations prior to use.
Conduits by the Inversion and Curing of a Resin-
1.5 This international standard was developed in accor-
Impregnated Tube
dance with internationally recognized principles on standard-
F3240 Practice for Installation of Seamless Molded Hydro-
ization established in the Decision on Principles for the
philic Gaskets (SMHG) for Long-Term Watertightness of
Development of International Standards, Guides and Recom-
Cured-in-Place Rehabilitation of Main and Lateral Pipe-
lines
4
2.2 NASSCO Guidelines:
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic
Recommended Specifications for Sewer Collection System
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
Rehabilitation.
Trenchless Plastic Pipeline Technology.
Current edition approved Nov. 15, 2022. Published December 2022. Originally
approved in 2006. Last previous edition approved in 2020 as F2599–20. DOI:
3. Terminology
10.1520/F2599-22.
2
The sectional repair of damaged pipe by means of inversion of a cured in place 3.1 Definitions:
liner is covered by patents The sectional repair of damaged pipe by means of
inversion of a cured in place liner is covered by patents 6,994,118, 7,975,726,
8,240,340,8,240,341,8,567,451,8,636,036,8,651,145,8,667,991,8,678,037,8,689,
3
835, 9,169,957, 9,366,375, 9,562,339, 9,551,449 (LMK Enterprises, Inc. 1779 For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Chessie Lane, Ottawa, IL 61350). Interested parties are invited to submit informa- contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
tionregardingtheidentificationofacceptablealternativestothispatenteditemtothe Standards volume information, refer to the standard’s Document Summary page on
Committee on Standards, ASTM Headquarters, 100 Barr Harbor Drive, West the ASTM website.
4
Conshohocken, PA 19428-2959. Your comments will receive careful consideration Available from 5285 Westview Drive Suite 202 Frederick, MD 21703,
at a meeting of the responsible technical committee which you may attend. http://www.nassco.org
*A Summary of Changes secti
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2599 − 20 F2599 − 22
Standard Practice for
Sectional Repair of Damaged Pipe By Means of an Inverted
1,2
Cured-In-Place Liner
This standard is issued under the fixed designation F2599; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice covers requirements and test methods for the sectional cured-in-place lining (SCIPL) repair of a pipe line (4 in.
through 60 in. (10.2 cm through 152 cm)) by the installation of a continuous resin-impregnated-textile tube into an existing host
pipe by means of air or water inversion and inflation. The tube is pressed against the host pipe by air or water pressure and held
in place until the thermoset resins have cured. When cured, the sectional liner shall extend over a predetermined length of the host
pipe as a continuous, one piece, tight fitting, corrosion resistant, and verifiable non-leaking cured-in-place pipe.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 There is no similar or equivalent ISO Standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
C1920 Practice for Cleaning of Vitrified Clay Sanitary Sewer Pipelines
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D1149 Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless Plastic
Pipeline Technology.
Current edition approved March 1, 2020Nov. 15, 2022. Published April 2020December 2022. Originally approved in 2006. Last previous edition approved in 20162020
as F2599–16.–20. DOI: 10.1520/F2599-20.10.1520/F2599-22.
2
The sectional repair of damaged pipe by means of inversion of a cured in place liner is covered by patents The sectional repair of damaged pipe by means of inversion
of a cured in place liner is covered by patents 6,994,118, 7,975,726, 8,240,340, 8,240,341,8,567,451, 8,636,036, 8,651,145, 8,667,991, 8,678,037, 8,689,835, 9,169,957,
9,366,375, 9,562,339, 9,551,449 (LMK Enterprises, Inc. 1779 Chessie Lane, Ottawa, IL 61350). Interested parties are invited to submit information regarding the identification
of acceptable alternatives to this patented item to the Committee on Standards, ASTM Headquarters, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Your
comments will receive careful consideration at a meeting of the responsible technical committee which you may attend.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2599 − 22
D3681 Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected
Condition
D5813 Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
F412 Terminology Relating to Plastic Piping Systems
F1216 Practice for Rehabilitation of Existing Pipelines and Conduits by the In
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.