EN 13481-2:2022
(Main)Railway applications - Track - Performance requirements for fastening systems - Part 2: Fastening systems for concrete sleepers in ballast
Railway applications - Track - Performance requirements for fastening systems - Part 2: Fastening systems for concrete sleepers in ballast
This document is applicable to fastening systems in Categories A - E as specified in EN 13481-1:2012, 3.1 for use on concrete sleepers in ballasted track with maximum axle loads and minimum curve radii as shown in Table 1.
[Table 1 - Fastening category criteria]
NOTE The maximum axle load for Categories A and B does not apply to maintenance vehicles.
The requirements apply to:
- fastening systems which act on the foot and/or web of the rail including direct fastening systems and indirect fastening systems;
- fastening systems for rail sections included in EN 13674-1 (excluding 49E4) or EN 13674-4.
This document is not applicable to fastening systems for other rail sections, rigid fastening systems or special fastening systems used at bolted joints or glued joints.
This document is for the type approval of complete fastening systems.
Bahnanwendungen - Oberbau - Leistungsanforderungen für Schienenbefestigungssysteme - Teil 2: Befestigungssysteme für Betonschwellen im Schotterbett
Dieses Dokument ist anzuwenden für Befestigungssysteme in den Kategorien A bis E, wie in EN 13481 1:2012, 3.1, festgelegt, für die Verwendung auf Betonschwellen im Schotteroberbau mit maximalen Auslegungsachslasten und Mindestbogenradien, wie in Tabelle 1 dargestellt.
Die Anforderungen gelten für:
— Befestigungssysteme, die am Schienenfuß und/oder Schienensteg wirken, einschließlich direkter und indirekter Befestigungssysteme;
— Befestigungssysteme für Schienenprofile nach EN 13674 1 (außer 49E4) oder EN 13674 4.
Dieses Dokument ist nicht anzuwenden für Befestigungssysteme für andere Schienenprofile, starre Befestigungssysteme oder spezielle Befestigungssysteme, die für verschraubte oder geklebte Schienenstöße verwendet werden.
Dieses Dokument gilt für die Typzulassung kompletter Befestigungssysteme.
Applications ferroviaires - Voie - Exigences de performance pour les systèmes de fixation - Partie 2 : Systèmes de fixation pour traverses en béton en voie ballastée
Le présent document est applicable aux systèmes de fixation des catégories A à E comme spécifiée dans l'EN 13481-1:2012, 3.1 pour utilisation sur des traverses en béton en voie ballastée avec des charges à l'essieu maximales et des rayons de courbure minimaux selon le Tableau 1.
[Tableau 1 - Critères de classification des systèmes de fixation]
NOTE La charge à l'essieu maximale pour les catégories A et B ne s'applique pas aux véhicules de maintenance.
Les exigences s'appliquent :
- aux systèmes de fixation qui agissent sur le patin et/ou l'âme du rail, y compris les systèmes de fixation directs et les systèmes de fixation indirects ;
- aux systèmes de fixation pour les profils de rail décrits dans l'EN 13674-1 (à l'exclusion du profil 49E4) et l'EN 13674-4.
Le présent document ne s'applique pas aux systèmes de fixation destinés à d'autres profils de rail, aux systèmes de fixation rigides, ou aux systèmes de fixation spéciaux utilisés au droit des éclisses.
Le présent document s’applique à l'homologation de type de systèmes de fixation complets.
Železniške naprave - Zgornji ustroj proge - Zahteve za izdelavo pritrdilnih sistemov - 2. del: Pritrdilni sistemi za betonske prage v tirni gredi
Ta evropski standard se uporablja za pritrdilne sisteme v kategorijah A do E iz točke 3.1 standarda EN 13481-1:2012 za betonske prage pri zgornjem ustroju s tamponskim slojem z največjo osno obremenitvijo in najmanjšim krivinskim polmerom, kot je prikazano v preglednici 1.
Preglednica 1 – Merila za kategorije pritrjevanja
Kategorija Največja osna obremenitev (kN) Najmanjši krivinski polmer (m)
A 130 40
B 180 80
C 260 150
D 260 400
E 350 150
OPOMBA: Največja osna obremenitev za kategoriji A in B ne velja za vzdrževalna vozila.
Zahteve se uporabljajo za:
– pritrdilne sisteme, ki delujejo na vznožje in/ali stojino tirnice, vključno z neposrednimi in posrednimi pritrdilnimi sistemi;
– pritrdilne sisteme z dinamično togostjo kLFA najmanj 50 MN/m;
– pritrdilne sisteme za dele železnice iz standarda EN 13674-1 (razen 49E4) ali EN 13674-4.
Ta standard se ne uporablja za pritrdilne sisteme za druge dele železnice, toge pritrdilne sisteme ali posebne pritrdilne sisteme, ki se uporabljajo pri zakovičenih spojih ali zlepljenih spojih.
Ta standard naj se uporablja le za odobritev tipa celotnih pritrdilnih sistemov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13481-2:2022
01-september-2022
Nadomešča:
SIST EN 13481-2:2012+A1:2017
Železniške naprave - Zgornji ustroj proge - Zahteve za izdelavo pritrdilnih sistemov
- 2. del: Pritrdilni sistemi za betonske prage v tirni gredi
Railway Applications - Track - Performance Requirements for Fastening Systems - Part
2: Fastening systems for concrete sleepers in ballast
Bahnanwendungen - Oberbau - Leistungsanforderungen für
Schienenbefestigungssysteme - Teil 2: Befestigungssysteme für Betonschwellen
Applications ferroviaires - Voie - Exigences de performance pour les systèmes de
fixation - Partie 2 : Systèmes de fixation pour traverses en béton en voie ballastée
Ta slovenski standard je istoveten z: EN 13481-2:2022
ICS:
93.100 Gradnja železnic Construction of railways
SIST EN 13481-2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13481-2:2022
---------------------- Page: 2 ----------------------
SIST EN 13481-2:2022
EN 13481-2
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2022
EUROPÄISCHE NORM
ICS 93.100 Supersedes EN 13481-2:2012+A1:2017
English Version
Railway applications - Track - Performance requirements
for fastening systems - Part 2: Fastening systems for
concrete sleepers in ballast
Applications ferroviaires - Voie - Exigences de Bahnanwendungen - Oberbau -
performance pour les systèmes de fixation - Partie 2 : Leistungsanforderungen für
Systèmes de fixation pour traverses en béton en voie Schienenbefestigungssysteme - Teil 2:
ballastée Befestigungssysteme für Betonschwellen
This European Standard was approved by CEN on 8 May 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13481-2:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13481-2:2022
EN 13481-2:2022 (E)
Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Symbols . 9
5 Requirements determined by laboratory testing . 9
5.1 Specimens used for laboratory testing . 9
5.2 Longitudinal rail restraint . 10
5.2.1 General case . 10
5.2.2 Special case for long structures .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.