ISO/TS 20490:2024

FINAL
TECHNICAL ISO/DTS
DRAFT
SPECIFICATION 20490
ISO/TC 42
Measuring autofocus repeatability of
Secretariat: ANSI
sharpness and latency
Voting begins on:
2023-12-11
Mesure de la répétabilité de la netteté et de la latence de l’autofocus
Voting terminates on:
2024-02-05
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/DTS 20490:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/DTS 20490:2023(E)
FINAL
TECHNICAL ISO/DTS
DRAFT
SPECIFICATION 20490
ISO/TC 42
Measuring autofocus repeatability of
Secretariat: ANSI
sharpness and latency
Voting begins on:
Mesure de la répétabilité de la netteté et de la latence de l’autofocus
Voting terminates on:
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/DTS 20490:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/DTS 20490:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions and abbreviated terms . 1
4 Test description . 2
4.1 General . 2
4.2 Test device settings . 2
4.3 Environmental conditions . 2
4.4 Apparatus and hardware . 2
4.5 Test distance . 4
4.6 Test charts . 5
4.6.1
...

Style Definition
...
Style Definition
...
Style Definition
ISO/DTS 20490:2023(E) .
Style Definition
...
ISO /TC 42/WG 18
Style Definition
...
Style Definition
Secretariat: ANSI
...
Style Definition
...
Date: 2023-10-24xx
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
Measuring auto-focusautofocus repeatability of sharpness and
...
Style Definition
latency .
Style Definition
...
Mesure de la répétabilité de la netteté et de la latence de l’autofocus
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...
Style Definition
...

---------------------- Page: 1 ----------------------
ISO/DTS 20490:2023(:(E)
Formatted: Font: 11 pt
Formatted: Font: 11 pt
Formatted: Header, Space After: 0 pt, Line spacing:
© ISO 2023
single
Formatted: Left: 1.9 cm, Right: 1.9 cm, Bottom: 1 cm,
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
Gutter: 0 cm, Header distance from edge: 1.27 cm,
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
Footer distance from edge: 0.5 cm
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester. Commented [eXtyles1]: The reference is to a withdrawn
standard which has been replaced

ISO copyright office
ISO 20344, Personal protective equipment — Test methods
CP 401 • Ch. de Blandonnet 8
for footwear
CH-1214 Vernier, Geneva
Formatted: Default Paragraph Font
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Formatted: Default Paragraph Font
Website: www.iso.orgwww.iso.org
Formatted: No page break before, Adjust space
between Latin and Asian text, Adjust space between
Published in Switzerland
Asian text and numbers
Formatted: Adjust space between Latin and Asian text,
Adjust space between Asian text and numbers
Formatted: French (Switzerland)
Formatted: French (Switzerland)
Formatted: French (Switzerland)
ii © ISO 2023 – All rights reserved
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DTS 20490:2023(:(E)
Formatted: Font: 11 pt
Formatted: Font: 11 pt
Formatted: Header, Left, Space After: 0 pt, Line spacing:
Contents
single
Foreword .vi
Introduction. vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions and abbreviated terms . 1
4 Test description . 2
4.1 General . 2
4.2 Test device settings . 2
4.3 Environmental conditions . 2
4.4 Apparatus and hardware . 2
4.5 Test distance .
...